Skip to main content

Boiler

Marine Boilers

Whether it is steam powered or has a diesel engine as the main form of propulsion, a ship without a boiler is really difficult to imagine. Boiler is an equipment that will be found on ship in some or the other form . For example if a ship is a steam powered ship, two or more boilers will be provided to produce steam having very high temperature and pressure; while if a ship is carrying a diesel engine as the main propulsion system, one or two smaller boilers are used for running various ship's machinery and services. So let us find out in this article as to how boilers work and what is their construction.

How do Boilers Work?

A basic boiler is a machine with the simplest arrangement of the internal parts. The main job of a boiler is to make high pressure steam. The feed water supplied to the boiler drum utilizes the heat of the energy released by burning the fuel. This energy of the burning fuel is stored in the form of steam with high temperature and pressure. The fuel is burnt in a combustion chamber inside the boiler. To attain high efficiency and complete combustion, air is supplied to this combustion chamber through a separate arrangement. The heat generated in this combustion chamber is transferred to the water from the boiler drum through a large surface area, which enables highest rate of energy transfer.

Steam Generation Process

The process of steam generation initiates when the feed water enters the steam drum. The water from the steam drums enters the water drum through both internal tubes and the tubes that surround the furnace. The system of tubes that surrounds the furnace are known as waterwall or floor tubes. The feed water gets heated when passed through these tubes. Addition to this, there are Large-bore downcomer tubes that passes outside of the furnace and are used to circulate water between the drums, to which the tubes are attached from outside of the furnace.

The steam produced in the steam drum is known as wet or saturated steam. This steam cannot be used directly as it contains high amount of moisture. To make this steam usable, it is first dried and heated with the help of a super heater located within the boiler. Once all the moisture content is removed from the steam, the super-heated steam can be supplied to other systems. It is utmost important to monitor and control the temperature of the superheated steam, or else it can cause damage to the systems it is supplied to. For this reason, an implement known as attemperator is used. Attemperator is a kind of cooler which is used to cool down the superheated steam to the right temperature. Thus, all the steam used in various system is taken out from the main steam drum of the boiler.

The energy from the fuel burning are used for various other purposes, the main two are as follows:

1. for heating feed water to produce steam

2. for superheating the steam from the boiler drum

To increase the efficiency of the boiler, the feed water that enters the boiler is pre-heated with the help of an economizer through which, the feed water passes before entering the boiler. The exhaust gas of the boiler is also put to use by making it pass over an air heater, which heats up the combustion air entering the furnace. Thus, even the energy exhausted from the boiler is allowed to go waste which increases the overall efficiency of the system.

All these boilers are fitted with various safety fittings and control system to monitor and control various aspects such as fuel oil flow rate, flow of combustion air and feed water supply. All these systems should work in co-ordination to supply the amount of steam required by various system. The boiler is also provided with various mounting to ensure safe operation of the boiler.

Types of Boilers

There are two main types of boilers. These are known as the basic boilers, the rest all are different versions of them. The main two basic boilers are:

  • Water Tube Boiler
  • Fire Tube Boiler

The design and arrangement of both the types is just the opposite. In water tube boilers, the feed water passes through the tubes and the hot gases are made to pass over them, while in fire tube boiler, the hot gases passes through the tubes and feed water surrounds them. We will talk about both these types of boilers and their variants in our future articles



Read more: http://www.brighthub.com/engineering/marine/articles/43728.aspx#ixzz3qG6KNhE1

Comments

Post a Comment

Popular posts from this blog

Shaftline 1.rudder stock, 2.rudder, 3.propeller bonnet, 4.propeller, 5.stern frame, 6.stern tube sealing, 7.stern tube bearings 8.stern tube, 9.propeller shaft, tail shaft, 10.plummer Mock, pillow block, shaft block, 11.intermediate shaft, 12.thrust shafts 13.flywheel, 14.crankshaft, shaft alley, shaft tunnel,
Post a Comment
Read more

Fresh Water Generator

Converting Seawater to Freshwater on a Ship: Fresh Water Generator Explained Fresh water generator , one of the important machinery on board a ship, is something that cannot be done without. Fresh water produced from fresh water generator is used for drinking, cooking, washing and even running other important machinery which use fresh water as a cooling medium. Fresh water is generally produced on board using the evaporation method. There are two things that are available in plenty on ship to produce fresh water –Seawater and heat. Thus fresh water is produced by evaporating sea water using heat from any of the heat source. The evaporated sea water is then again cooled by the sea water and the cycle repeats. Generally the heat source available is taken from the main engine jacket water, which is used for cooling the main engine components such as cylinder head, liner etc. The temperature available from this jacket water is about 70 deg. centigrade. But at this temperature the evaporati...
3 comments
Read more
FUEL INJECTION EQUIPMENT There are three methods commonly used for the mechanical injection of fuel (at the proper amount, time, and duration) into the cylinders of a diesel engine. These methods are as follows: 1. Pump controlled (jerk pump) 2. Distributor 3. Unit injector NOTE: A fourth method, known as pressure-time (PT) uses unit injectors. This method is unique to Cummins diesel engines and is not considered to be common; therefore, it will not be explained in this rate training manual. The three methods listed above will be explained in the sections that follow. JERK PUMP FUEL INJECTION SYSTEM Jerk pump fuel injection systems consist of high-pressure pumps and pressure-operated spray valves or nozzles that are separate components. In some engines, such as the Alco, there is only one pump and one nozzle for each cylinder. In other engines, such as the Fairbanks-Morse opposed-piston engine, each cylinder has two pumps and two nozzles. Most of the injection event is carried out by t...
1 comment
Read more